Chemtrol Australia Product - IK-739-PLUS & IK-736-PLUS Auto-Brushing Turbidity Analyzers

Looking for a quote or to discuss your needs?

You can also review the documentation for technical details and purchasing information.

IK-739-PLUS & IK-736-PLUS Auto-Brushing Turbidity Analyzers

Product Details
Specifications
Drinking & Process Water
Installation

IK-739-PLUS & IK-736-PLUS Auto-Brushing Turbidity Analyzers

The Pyxis IK-73X-PLUS analysers measure turbidity continuously, with a resolution of 0.002 NTU. Each one comes complete on a single wall panel, set up, tested and calibrated at the factory. Connect the sample line, the drain and the power, and it is ready to run.

IK-739-PLUS: 0.000 – 40.00 NTU, with the LT-739 sensor
IK-736-PLUS: 0.000 – 1,000 NTU, with the LT-736 sensor

The panel holds the turbidity sensor in its brushing flow cell, an FS-100 ultrasonic flow meter with a motorised valve that keeps the sample flow at a set rate, and a 7-inch touch screen that displays, logs and passes on the readings.

A Brush Keeps the Lens Clean

The sensor looks through a flat quartz window. A motorised brush in the FT-100-PLUS flow cell wipes it as often as you set, so fouling can’t build up, and the flat window stops air bubbles settling on it. The reading stays steady with very little attention.

Specifications

Item	IK-739-PLUS	IK-736-PLUS
Part Number	12001	12003
Turbidity Range	0.000 – 40.00 NTU	0.000 – 1,000 NTU
Sensor	LT-739	LT-736
Light Source	Warm white LED, 90° surface scatter
Method	USEPA 180.1 (US)
Accuracy	0.001 NTU or ±1% of full scale
Resolution	0.002 NTU
Response Time	4 seconds
Measurement	Continuous
Flow Cell	FT-100-PLUS with motorised brush
Display	7-inch colour capacitive touch screen
Data Storage	4 GB, up to 1 million readings and events
Outputs	Two 4–20 mA, RS-485 Modbus RTU, Modbus TCP
Inputs	Two 4–20 mA, RS-485 Modbus RTU
USB	One USB host port, for data download and screen updates
Network	RJ-45 Ethernet, Modbus TCP
Power Supply	96 – 260 V AC, 50/60 Hz, 200 W, 10 A fuse
Sample Pressure	0.05 – 0.67 MPa (7.25 – 100 psi)
Sample Flow	100 – 2,000 mL/min
Sample Temperature	4 – 40 °C (40 – 104 °F)
Panel Operating Temperature	4 – 45 °C (40 – 113 °F)
Storage Temperature	Instrument −20 – 55 °C (−4 – 131 °F); sensors 0 – 50 °C (32 – 122 °F)
Sample Connections	½" NPT
Flow Meter	FS-100 ultrasonic (transit time), 0 – 3,000 mL/min, 1 mL/min or ±2% of reading, 1.44" colour display
Protection	IP65 panel display, IP67 sensors
Relative Humidity	20 – 90%, non-condensing
Altitude	Up to 2,000 m (6,561 ft)
Dimensions	750 H × 450 W × 243 D mm
Weight	About 15 kg
Approvals	CE, RoHS

Spare Parts and Calibration

Part	Part Number
FT-100-PLUS auto-brushing flow cell	16005
FTP-100-1 brush and seal kit for FT-100-PLUS	28698
LT-739 turbidity sensor, 0 – 40 NTU	53221
LT-736 turbidity sensor, 0 – 1,000 NTU	53215
FS-100 ultrasonic flow meter with display	54200
UC-100A display and data logger	43054
L-CAL portable calibration kit	53247
Turbidity standard 10 NTU, 500 mL	57010-4
Turbidity standard 30 NTU, 500 mL	57010-8
Turbidity standard 500 NTU, 500 mL	57010-2

The IK-73X-PLUS is for sites where turbidity has to be watched around the clock: drinking water and secondary supply, raw surface water, cooling and process water, and wastewater effluent. It runs on a mains plug, logs every reading on the panel, and sends the results on to a PLC or SCADA system.

Key Features

Resolution 0.002 NTU; range 0 – 40 NTU or 0 – 1,000 NTU
Warm white LED at 90° scatter, to USEPA 180.1 (US)
Motorised brush cleans the sensor window on a programmable cycle
Flat quartz window resists air-bubble interference
FS-100 ultrasonic flow meter and motorised valve hold the sample flow steady, with a no-flow alarm
7-inch colour touch screen with calibration and diagnostics built in
Stores up to 1 million readings and events, downloaded by USB
Two 4–20 mA outputs, RS-485 Modbus RTU and Modbus TCP over Ethernet; two 4–20 mA inputs
Set up, tested and calibrated at the factory
Calibrated on site with the L-CAL portable calibration kit

Mounting: wall panel 750 H × 450 W × 243 D mm, about 15 kg. Use fixings rated for the weight.
Power: plugs into a standard mains outlet.
Sample: inlet pressure 0.05 – 0.67 MPa (7.25 – 100 psi), flow 100 – 2,000 mL/min, water 4 – 40 °C.
Connections: ½” NPT inlet and outlet. The outlet must drain by gravity.
Upkeep: clean the sensor and flow cell monthly or as needed, replace the brush head yearly, and calibrate every six months (the low point only, for clean water).